NETGEAR CG834WG User Manual Download | Manualshive

Page: 15 / 64

background image

Wireless Cable Modem Gateway CG834WG User Manual

1-3

v1.0, October 2007

Rear Panel

The rear panel of the CG834WG contains the connections identified below:

What You Need Before You Begin

You need these three things before you can connect your gateway to the Internet:

•

A computer properly connected to the gateway as explained below.

•

Active Data Over Cable Internet service provided by cable modem account.

•

The Internet Service Provider (ISP) configuration information for your cable modem account.

Hardware Requirements

The CG834WG Gateway connects to your LAN using either its twisted-pair Ethernet, USB or
802.11b or 802.11g wireless port.

To use the CG834WG Gateway on your network, each computer must have either an installed
Ethernet Network Interface Card (NIC), USB Host port or 802.11b or 802.11g wireless adapter. If
the computer will connect to your network at 100 Mbps, you must use a Category 5 (CAT5) cable
such as the one provided with your gateway.

Figure 1-2

AC power adapter input

wireless antenna

reset button

USB port

4 Ethernet LAN ports

coaxial cable to your cable service provider

«
...
13
14
15
16
17
...
»

Summary of Contents for CG834WG

































































Reviews:

No comments

Related manuals for CG834WG

Brand: Qtel Pages: 28

MicroLink ADSL Modem

Brand: Devolo Pages: 41

Brand: Paradyne Pages: 2

Brand: Paradyne Pages: 4

COMSPHERE 3920PLUS Series

Brand: Paradyne Pages: 356

Brand: Zte Pages: 2

Brand: Blonder tongue Pages: 20

Brand: Lantronix Pages: 125

Brand: Davicom Pages: 27

Brand: Davicom Pages: 29

Brand: Blonder tongue Pages: 12

Brand: C-motech Pages: 15

Brand: 3Com Pages: 56

Brand: 3Com Pages: 66

U.S. Robotics 56K Voice

Brand: 3Com Pages: 85

Brand: CTC Union Pages: 26

Brand: Lanpro Pages: 3

Brand: Campbell Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands