manualshive.com logo in svg

NEC N8100-1909F, Maintenance Manual, Page: 111 / 126

Share
Download
NEC N8100-1909F Maintenance Manual Download Page 111

1. POST Error Message 

 

Express5800/E120d-M  Maintenance Guide 

 

111 

Chapter 3 Appendix 
 

Error Message 

Cause 

Solution 

C10B 

BMC operational code 

corrupted. 

Failed to start BMC firmware. 

Unplug the power cord, wait for at least 30 
seconds, then restart the server. If the same 
error is detected repeatedly, contact your 
sales representative. 

C10C 

BMC update firmware 

corrupted.  

C10D 

Internal Use Area of BMC FRU 

corrupted.   

An illegality was detected in FRU 
containing the device information. 

C10E 

BMC SDR Repository empty.  

An error was detected on BMC SDR. 

C10F 

IPMB signal lines do not 

respond.  

Failure of Satellite Management 
Controller was detected. 

C110 

BMC FRU device failure.  

An error was detected in FRU that 
contains device information. 

C111 

BMC SDR Repository failure.   

Failure was detected in SROM that 
stores the SDR. 

C112 

BMC SEL device failure.  

Device failure was detected in BMC 
SEL. 

C113 

BMC RAM test error.  

An error was detected in BMC RAM. 

C114 

BMC Fatal hardware error.  

A hardware error was detected in 
BMC. 

C115 

Management controller 

not responding 

Management controller does not 
respond. 

Update the BMC firmware.   
If the same error is detected repeatedly, 
contact your sales representative. 

C116 

Private I2C bus not 

responding. 

Private I2C bus does not respond. 

Unplug the power cord, wait for at least 30 
seconds, then restart the server. If the same 
error is detected repeatedly, contact your 
sales representative. 

C117 

BMC internal exception 

BMC internal error was detected. 

C118 

BMC A/D timeout error. 

BMC A/D timeout error was 
detected. 

C119 

SDR repository corrupt. 

BMC error or illegal SDR data was 
detected. 

Unplug the power cord, wait for at least 30 
seconds, then restart the server. If the same 
error is detected repeatedly, contact your 
sales representative. 

C11A 

SEL corrupt. 

BMC error or illegal system event log 
data was detected. 

C11B 

BMC Mezzanine card is not 

found. 

BMC Mezzanine card is not installed.  Contact your sales representative. 

C11C 

BMC Mezzanine partition is 

invalid. 

A format error was detected in BMC 
Mezzanine card. 

C11D 

BMC is in Forced Boot Mode. 

Detected that BMC is in Forced Boot 
Mode. 

Check the jumper switch setting on 
motherboard. Unplug the power cord, wait 
for at least 30 seconds, then restart the 
server. If the same error is detected 
repeatedly, contact your sales 
representative. 

C200 

The error occurred during 

memory configuration 

check. 

Memory configuration could not be 
obtained. 

Contact your sales representative. 

C201 

Memory Configuration 

change is detected. 

The memory configuration has 
changed since the previous startup. 

When 

Check previous system Config

 is 

enabled in 

Server

 of the setup, this 

message appears if the configuration was 
changed since the previous startup. If this 
message appears even when no 
configuration change has been made, 
contact your service representative.   

Summary of Contents for N8100-1909F































































































































Reviews:

No comments