manualshive.com logo in svg

NEC N8100-1909F, Maintenance Manual, Page: 106 / 126

Share
Download
NEC N8100-1909F Maintenance Manual Download Page 106

1. POST Error Message 

 

Express5800/E120d-M  Maintenance Guide 

 

106 

Chapter 3 Appendix 
 

Error Message 

Cause 

Solution 

8006 

System configuration data 

cleared by Jumper. 

The system configuration data was 
cleared by the jumper. 

Follow the steps described in 

Chapter 1 (7. 

Resetting and Clearing the Server). 

Start SETUP, and then setup each item 
again.   
If the same error is detected repeatedly in 
spite of re-setting, contact your sales 
representative. 
This error message also appears when 
lithium battery is removed. 

8007 

SETUP Menu Password cleared 

by Jumper. 

The password set in SETUP was 
cleared by the jumper. 

Follow the steps described in 

Chapter 1 (7. 

Resetting and Clearing the Server). 

Run SETUP and set your password again. 
If the same error is detected repeatedly in 
spite of re-setting, contact your sales 
representative. 

8020 

BIOS update error. 

BIOS update failed. 

If the same error is detected repeatedly, take 
measures by referring the error information 
in BIOS release note, or contact your sales 
representative. 

8021 

Recovery jumper is set, but 

recovery images is not 

found. 

Recovery jumper is set, but recovery 
of BIOS failed. 

Contact your sales representative. 

8800 

DXE_NB_ERROR 

An error was detected during 
initialization of chipset. 

8801 

DXE_NO_CON_IN 

An error was detected during 
initialization of console. 

8802 

DXE_NO_CON_OUT 

8803 

PEI_DXE_CORE_NOT_FOUND 

BIOS Flash ROM failed. 

8804 

PEI_DXEIPL_NOT_FOUND 

8805 

DXE_ARCH_PROTOCOL_NOT_AVA

ILABLE 

8806 

PEI_RESET_NOT_AVAILABLE 

The system was not reset correctly. 

8807 

DXE_RESET_NOT_AVAILABLE 

8808 

DXE_FLASH_UPDATE_FAILED 

Failed to write in BIOS Flash ROM. 

8830 

PEI_RECOVERY_NO_CAPSULE 

Failed to recover BIOS Flash ROM. 

8831 

PEI_RECOVERY_PPI_NOT_FOUN

D 

8832 

PEI_RECOVERY_FAILED 

9000 

Unsupported CPU 

detected 

An unsupported CPU was detected. 

9001 

Unsupported CPU 

detected on CPU #1 

9002 

Unsupported CPU 

detected on CPU #2 

9021 

Unsupported CPU Speed 

detected on CPU #1 

A CPU of which clock speed is 
unsupported was detected. 

9022 

Unsupported CPU Speed 

detected on CPU #2 

Summary of Contents for N8100-1909F































































































































Reviews:

No comments