NEC 78K0S/KB1+ User Manual Download Page 393

Page: 393 / 406

APPENDIX D LIST OF CAUTIONS

User’s Manual U17446EJ3V1UD

393

(11/19)

Chapter

assi

cati

Function

Details of

Function

Cautions Page

RXB6: Receive

buffer register 6

Reception enable status is entered, after having set RXE6 to 1 and one clock

of the base clock (f

XCLK6

) has elapsed.

p.185

When starting transmission, write transmit data to TXB6, after having set TXE6

to 1 and a wait of one clock or more of the base clock (f

XCLK6

) has been

performed.

p.185

Do not write data to TXB6 when bit 1 (TXBF6) of asynchronous serial interface

transmission status register 6 (ASIF6) is 1.

p.185

TXB6: Transmit

buffer register 6

Do not refresh (write the same value to) TXB6 by software during a

communication operation (when bit 7 (POWER6) and bit 6 (TXE6) of

asynchronous serial interface operation mode register 6 (ASIM6) are 1 or

when bit 7 (POWER6) and bit 5 (RXE6) of ASIM6 are 1). When outputting

same values in continuous transmission, be sure to confirm that TXBF6 is 0

before writing the same values to TXB6.

p.185

At startup, transmission operation is started by setting TXE6 to 1 after having

set POWER6 to 1, then setting the transmit data to TXB6 after having waited

for one clock or more of the base clock (f

XCLK6

). When stopping transmission

operation, set POWER6 to 0 after having set TXE6 to 0.

p.187

At startup, reception enable status is entered after having set POWER6 to 1,

then setting RXE6 to 1, and one clock of the base clock (f

XCLK6

) has elapsed.

When stopping reception operation, set POWER6 to 0 after having set RXE6

to 0.

p.188

Set POWER6 = 1

→

RXE6 = 1 in a state where a high level has been input to

the RxD6 pin. If POWER6 = 1

→

RXE6 = 1 is set during low-level input,

reception is started and correct data will not be received.

p.188

Clear the TXE6 and RXE6 bits to 0 before rewriting the PS61, PS60, and CL6

bits.

p.188

Fix the PS61 and PS60 bits to 0 when the interface is used in LIN

communication operation.

p.188

Make sure that TXE6 = 0 when rewriting the SL6 bit. Reception is always

performed with “the number of stop bits = 1”, and therefore, is not affected by

the set value of the SL6 bit.

p.188

ASIM6:

Asynchronous

serial interface

operation mode

Make sure that RXE6 = 0 when rewriting the ISRM6 bit.

p.188

The operation of the PE6 bit differs depending on the set values of the PS61

and PS60 bits of asynchronous serial interface operation mode register 6

(ASIM6).

p.188

The first bit of the receive data is checked as the stop bit, regardless of the

number of stop bits.

p.188

If an overrun error occurs, the next receive data is not written to receive buffer

p.188

pp.

Chapter 1

Soft

Serial

interface

UART6

ASIS6:

Asynchronous

serial interface

reception error

status register 6

Be sure to read ASIS6 before reading receive buffer register 6 (RXB6).

188, 206

Summary of Contents for 78K0S/KB1+























































































































































































































































































































































































































Search results

Summary of Contents for 78K0S/KB1+

Reviews:

Related manuals for 78K0S/KB1+

Brands by name

Popular brands

NEC 78K0S/KB1+, User Manual

Search results

Summary of Contents for 78K0S/KB1+

Reviews:

Related manuals for 78K0S/KB1+

Brands by name

Popular brands