NEC 78K0S/KB1+ User Manual Download Page 87

Page: 87 / 406

CHAPTER 6 16-BIT TIMER/EVENT COUNTER 00

User’s Manual U17446EJ3V1UD

(1) 16-bit timer counter 00 (TM00)

TM00 is a 16-bit read-only register that counts count pulses.

The counter is incremented in synchronization with the rising edge of the count clock. If the count value is read

during operation, input of the count clock is temporarily stopped, and the count value at that point is read.

Figure 6-2. Format of 16-bit Timer Counter 00 (TM00)

TM00

Symbol

FF13H

FF12H

Address: FF12H, FF13H After reset: 0000H R

The count value is reset to 0000H in the following cases.

<1> At reset signal generation

<2> If TMC003 and TMC002 are cleared

<3> If the valid edge of TI000 is input in the clear & start mode entered by inputting the valid edge of TI000

<4> If TM00 and CR000 match in the clear & start mode entered on a match between TM00 and CR000

<5> If OSPT00 is set to 1 in the one-shot pulse output mode

Cautions 1. Even if TM00 is read, the value is not captured by CR010.

2. When TM00 is read, count misses do not occur, since the input of the count clock is

temporarily stopped and then resumed after the read.

(2) 16-bit timer capture/compare register 000 (CR000)

CR000 is a 16-bit register which has the functions of both a capture register and a compare register. Whether

it is used as a capture register or as a compare register is set by bit 0 (CRC000) of capture/compare control

CR000 is set by 16-bit memory manipulation instruction.

Reset signal generation clears this register to 0000H.

Figure 6-3. Format of 16-bit Timer Capture/Compare Register 000 (CR000)

CR000

Symbol

FF15H

FF14H

Address: FF14H, FF15H After reset: 0000H R/W

•

When CR000 is used as a compare register

The value set in CR000 is constantly compared with the 16-bit timer/counter 00 (TM00) count value, and an

interrupt request (INTTM000) is generated if they match. It can also be used as the register that holds the

interval time then TM00 is set to interval timer operation.

<R>

Summary of Contents for 78K0S/KB1+























































































































































































































































































































































































































Search results

Summary of Contents for 78K0S/KB1+

Reviews:

Related manuals for 78K0S/KB1+

Brands by name

Popular brands

NEC 78K0S/KB1+, User Manual

Search results

Summary of Contents for 78K0S/KB1+

Reviews:

Related manuals for 78K0S/KB1+

Brands by name

Popular brands