NEC 78K0S/KB1+ User Manual Download Page 142

Page: 142 / 406

CHAPTER 8 8-BIT TIMER H1

User’s Manual U17446EJ3V1UD

142

8.4.2

Operation as PWM output mode

In PWM output mode, a pulse with an arbitrary duty and arbitrary cycle can be output.

8-bit timer compare register 01 (CMP01) controls the cycle of timer output (TOH1). Rewriting the CMP01 register

during timer operation is prohibited.

8-bit timer compare register 11 (CMP11) controls the duty of timer output (TOH1). Rewriting the CMP11 register

during timer operation is possible.

The operation in PWM output mode is as follows.

TOH1 output becomes active and 8-bit timer counter H1 is cleared to 0 when 8-bit timer counter H1 and the

CMP01 register match after the timer count is started. TOH1 output becomes inactive when 8-bit timer counter H1

and the CMP11 register match.

(1) Usage

In PWM output mode, a pulse for which an arbitrary duty and arbitrary cycle can be set is output.

<1> Set each register.

Figure 8-8. Register Setting in PWM Output Mode

(i) Setting timer H mode register 1 (TMHMD1)

0/1

TMMD10 TOLEV1

TOEN1

CKS11

CKS12

TMHE1

TMHMD1

CKS10

TMMD11

Timer output enabled

Timer output level inversion setting

PWM output mode selection

Count clock (f

CNT

) selection

Count operation stopped

(ii) Setting CMP01 register

•

Compare value (N): Cycle setting

(iii) Setting CMP11 register

•

Compare value (M): Duty setting

Remark

00H

≤

CMP11 (M) < CMP01 (N)

≤

FFH

<2> The count operation starts when TMHE1 = 1.

<3> The CMP01 register is the compare register that is to be compared first after count operation is enabled.

When the values of 8-bit timer counter H1 and the CMP01 register match, 8-bit timer counter H1 is cleared,

an interrupt request signal (INTTMH1) is generated, and TOH1 output becomes active. At the same time,

the compare register to be compared with 8-bit timer counter H1 is changed from the CMP01 register to the

CMP11 register.

Summary of Contents for 78K0S/KB1+























































































































































































































































































































































































































Search results

Summary of Contents for 78K0S/KB1+

Reviews:

Related manuals for 78K0S/KB1+

Brands by name

Popular brands

NEC 78K0S/KB1+, User Manual

Search results

Summary of Contents for 78K0S/KB1+

Reviews:

Related manuals for 78K0S/KB1+

Brands by name

Popular brands