NEC 78K0S/KB1+ User Manual Download

Page: 102 / 406

CHAPTER 6 16-BIT TIMER/EVENT COUNTER 00

User’s Manual U17446EJ3V1UD

102

(1) Pulse width measurement with free-running counter and one capture register

Specify both the rising and falling edges as the valid edges of the TI000 pin, by using bits 4 and 5 (ES000 and

ES010) of PRM00.

When 16-bit timer counter 00 (TM00) is operated in free-running mode, and the valid edge specified by

PRM00 is input, the value of TM00 is taken into 16-bit timer capture/compare register 010 (CR010) and an

external interrupt request signal (INTTM010) is set.

Sampling is performed using the count clock selected by PRM00, and a capture operation is only performed

when a valid level of the TI000 pin is detected twice, thus eliminating noise with a short pulse width.

Caution The measurable pulse width in this operation example is up to 1 cycle of the timer counter.

Figure 6-18. Control Register Settings for Pulse Width Measurement with Free-Running Counter

and One Capture Register (When TI000 and CR010 Are Used)

(a) Capture/compare control register 00 (CRC00)

CRC002

CRC001

0/1

CRC000

CRC00

CR000 used as compare register

CR010 used as capture register

(b) Prescaler mode register 00 (PRM00)

ES101

0/1

ES100

0/1

ES010

ES000

PRM001

0/1

PRM000

0/1

PRM00

Selects count clock (setting “11” is prohibited).

Specifies both edges for pulse width detection.

Setting invalid (setting “10” is prohibited.)

(c) 16-bit timer mode control register 00 (TMC00)

TMC003

TMC002

TMC001

0/1

OVF00

TMC00

Free-running mode

Remark

0/1: Setting 0 or 1 allows another function to be used simultaneously with pulse width measurement.

See the description of the respective control registers for details.

Summary of Contents for 78K0S/KB1+























































































































































































































































































































































































































Search results

Summary of Contents for 78K0S/KB1+

Reviews:

Related manuals for 78K0S/KB1+

Brands by name

Popular brands

NEC 78K0S/KB1+, User Manual

Search results

Summary of Contents for 78K0S/KB1+

Reviews:

Related manuals for 78K0S/KB1+

Brands by name

Popular brands