background image

[ 134 ]  

NATIONAL RAMP

 | FREEDOM 

NOW    

www.nationalramp.com | 877-884-RAMP(7267)

The 100% aluminum ramp system does not require special maintenance, as it will not rust or corrode. 
The ramp must be kept free of debris. Use a stiff broom to clear the ramp of leaves and light snow.

In the event of heavy snow, use a calcium chloride or magnesium chloride ice melt, which is safe for 
the ramp’s aluminum surface. Avoid using metal shovels, and if using a snowblower, be very careful 
when close to the ramp surface. Use a plastic shovel or stiff broom to clear the ramp surface directly.

The ramp should periodically be checked to ensure that connections remain tight, and parts such as 
Celebration Footer Pads™, corner covers and leg caps are still placed properly.

Do not allow children to play on or near the ramp. Do not hang items off of the ramp or use the ramp 
for storage. 

The ramp comes with a lifetime warranty for any defects. This warranty does not cover damage 
the ramp may incur by falling trees/branches, if the ramp is hit by a vehicle, or damage caused by 
a storm, for example. If you believe that your Liberty System ramp has a defect, 

call National Ramp 

at (877) 884-7267

23. Liberty Series

TM

 Maintenance And Care

Summary of Contents for ALUMINUM SOLID











































































































































Reviews: