© by N&W GLOBAL VENDING S.p.A.
29
07 - 2010 3375 - 01
D
rippiNg
You can define the wait time (you can programme it from
0 to 2000 hundredths of a second) from the end of deliv
-
ery to the closure of the shift arm for every single selec-
tion to leave the tubes enough time to get empty.
s
ElEcTioN
sTaTus
You can define for every single selection key whether to
enable it or not.
a
ccEssoriEs
For every single accessory:
sugar
on/off
-
stirrer
on/off
-
cup
on/off
-
sugar in the cup
(dose in gr.)
-
you can decide whether to add it to a selection or not.
complETE
sElEcTioN
TEsT
Use this function to dispense the following for every sin-
gle selection when the door is open and without inserting
the required amount:
- complete selection
- water only
- powder only
- no accessory (cup, sugar and stirrer)
- accessories only
p
roDucT
coDE
Use this function to assign a 16-alphanumeric character
identification code to every single selection for the pur
-
pose of processing statistics.
g
loBal
poWDEr
DosEs
Use this function to regulate the powder dose of every
single ingredient motor relative to several selections at
the same time.
p
ump
c
aliBraTioN
The speed and flow rate of direct current pumps can be
controlled electronically.
To adjust the control device to the actual flow rate, cali
-
brate the pumps, i.e. measure the actual flow rate at a
given speed.
the operation is performed at the factory, but you may
have to repeat it for various reasons.
after having found out the mixer where to act and con-
firmed the type of nozzles in use, the pump is operated
for a well-defined time at the minimum and maximum
speed by means of the corresponding menu. the system
can optimise the dispensing speed by storing the water
quantities you get.
i
NgrEDiENT
moTor
caliBraTioN
to convert the product dose values properly, set up the
flow rate value of every single ingredient motor in gr/s to
calculate the grams to be dispensed.
k
EyBoarD
k
Ey
<--->
sEl
Use this function to vary the order of the selections as-
sociated with the keyboard and defined by the layout you
have set up.
the display shows the list of available selections in
sequence. Press the destination key to store the asso-
ciation.
D
ouBlE
kEy
Use this function to join 2 keys arranged one next to the
other one vertically into one single key to use a double-
size key for one single selection.
s
ElEcTioN
No
.
cHEck
You can check the selection number associated with a
key (direct selection mode).
N
o
sugar
Use this function to set up all sugarless selections made
available by default (ON).
function valid on some models only.
D
Ecaff
cyclE
This function acts on instant coffee-based selections.
Selections are identified in the layout and their identifica
-
tion can not be changed.
If you enable this function in all coffee-based selections
(if made available), powder dispensing occurs before
water dispensing.
However, you can change this parameter one by one, for
every single instant coffee-based selection.
Fig. 23
Summary of Contents for Canto Plus Instant
