background image

  

15 of 32

www.NabcoEntrances.com

SwingandFoldDoorOpusControlWiringandProgrammingInstallationManual

Rev. 8-11-21 

P/N C-00139

Optional Setting

Parameter

Range

Default

Description

DN 1558

Open fi rst,

Latch check is wide

Overlap Sim Pair

Opus Se  ngs

Normal Sim Pair

Ac va on No Ac va on

Connec on

Flip Screen

Yes

No

Choose Yes if Opus is installed upside down. 

LCD will flip right side up when Control is upside down.

No

SECTION 8.4: Output Settings

Output Setting  

Parameter

Terminal

Default

Range

Description

Output 1 

Terminal 7

Fully Opened 

— — 

No Output

Position

Fully Closed Position

Output closes when fully closed

Output 2

Terminal 13 Fully Closed

Closing Status

Output closes when door is closing

Position

Opening Status

Output closes when door is opening

Relay Output 3 Relay Output

— — 

Fully Opened Position 

Output closes when door fully opened.

Terminals

Error State Output

Output closes when error detected

Recycle happened

Output closes when recycle occurs

Electric Strike Lock

Set for electric strike functionality (N.O.)

Electric Magnetic Lock

Set for Mag lock functionality (N.C.) 

Air lock

Set for Air lock functionality

Breakout Pass through

Output closes when breakout occurs

TrmnL H PassThrough

Output changes state when input H changes state

Door Sequencing

Provision for door sequencing

Sensor Monitoring (N.O.)

Normally open Monitoring circuit

 

(high logic)

Sensor Monitoring (N.C.)

Normally closed Monitoring ciruit

 

(low logic)

Bodyguard Output

Outputs data for bodyguard sensors and other 

sensors that utilize same data .

For Elite N Output

For Elite (N) sensor made by Optex. (Output 1 only) 

Open Delay

 

Timer

N/A

0.4

0.5, 1.0, 1.5 sec

After Unlock Input

Delay time after activation to allow lock to unlock 

before the door starts moving.

Only functional if Electric Lock is selected.

Sequence 

 

Delay Timer

N/A

0

0-10, 12, 15, 20, 25

Same as Open Timer

Delay Time before second Door opens when an output 

is being used for Door Sequencing.

Lock Condition N/A

Every Fully

Closed

Every Fully Closed

One way/Night Only

Determines when the electric lock engages.

Summary of Contents for C-00139

































Reviews: