If you're using the stop on our Ultra Track with a 3/4" sub-fence and
you're using our Ruler Bar too, you'll want to attach the cursor to the
back of the stop body. Install the two 3/16" washers
(WB001)
on the 5/8"
screw
(MT012)
, insert the screw thru the hole in the cursor
(4519C)
and start
a nut
(NUT004)
on the end of the screw. Slide the nut in the T-slot of the stop
body, adjust the cursor position on the Ruler Bar and tighten the screw.
Starting from the ribbed
side of the stop body,
insert the 1-1/2" hex bolt
(HB050)
thru the cross
hole in the stop
body and attach
the knob
(5540)
to the end of
the bolt.
Identify and verify that you have all the parts listed. Read the
instructions at least once, familiarizing yourself with the parts and
assembly options, before beginning assembly. This stop is designed
to be used on the top of our Ultra Track aluminum extrusion.
There are four basic ways to assemble the stop, depending on
whether you want the stop arm on the left or right side of the stop body,
and whether or not you'll be using a 3/4" sub-fence on the Ultra Track.
A:
If you're not using a 3/4" sub-fence, mount the
stop arm to the stop block so the T-slot in face of the stop
block faces the front of the track.
See two Straight Stops
shown on left in fig. 2 and stop block in fig. 1.
4516 Curved Stop
& 4519 Straight Stop
Please Read Carefully!
Part Desc . . . . . Qty
4516A
Curved Arm . . . . . . . . 1
or
4519A
Straight Arm . . . . . . . . 1
4519B
Stop Block . . . . . . . . . . 1
4519P
Pivot Pin . . . . . . . . . . . 1
4519C
Cursor . . . . . . . . . . . . . 1
5540
Knob . . . . . . . . . . . . . . . 1
HB050 1-1/2" hex bolt . . . . . . 1
Part Desc . . . . . Qty
WS001 1/4" Washer . . . . . . . . . 1
WN001 1/4" Washer . . . . . . . . . 1
MT012 5/8" Screw . . . . . . . . . . 1
WB001 3/16" Washer . . . . . . . 2
NUT004 10-24 Nut . . . . . . . . . . 2
NUT010A Locknut . . . . . . . . . . . . 1
MA002 10-24 Set Screw . . . . . 1
5786
3/32" Allen Wrench . 1
1
Parts List
NUT010A
on 4519P
Stop Arm:
4519A or
4516A
T-slot face of
Stop Block
NUT004 &
MA002
Allen
Wrench
WN001
5540
ASSEMBLY
Clamp the smooth portion of the
pivot pin
(4519P)
in a vise with non-
marring jaws and screw the locknut
(NUT010A)
on the threaded end of the pivot pin until
the nut is flush with the end of the pin.
Insert the 1/4" steel washer
(WS001)
on
the pivot pin (against the nut), followed
by the stop arm
(4516A or 4519A)
and the 1/4" nylon washer
(WN001)
.
Start the 10-24 set screw
(MA002)
in one of the 10-24 nuts
(NUT004)
.
Slide the nut/set screw into the T-slot
indicated in the stop block
(4519B)
.
Insert the smooth portion of the pivot pin
(4519P)
in the diamond/square shaped slot in the stop block
and, using the 3/32" allen wrench
(5786)
tighten the
set screw on the pivot pin, locking the pivot pin in the stop
body. Make sure the set screw nut is not rubbing against
the nylon washer on the pivot pin. Adjust the locknut on
the pivot pin to get the desired amount of tension on the
stop arm so it pivots as hard or as easy as you like.
A
B
C
D
E
F
NUT010A
flush with end
of 4519P
4519P Pivot Pin
B:
If you are using a 3/4" sub-fence, the rounded
edge of the stop block (opposite from the T-slot side)
should face the front of the track.
See two Straight Stops
shown on right in fig. 2 and stop block in fig. 1.
WS001
NUT004
MT012
WB001 x2
4519C
