Murr Elektronik IMPACT67-P Instruction Manual Download Page 33 | Manualshive

Page: 33 / 41

background image

IMPACT67-P manual

32

V

1.6

5.2 IMPACT67-P DI8 DO8

Technical data

Number of inputs / outputs .................................. 8
Operating voltage of actuator power supply  ...... 24 V ± 25% (18 V to 30.2 V) DC
Operating voltage of sensor power supply  ........ 24 V ± 25% (18 V to 30.2 V) DC
Power supply (module electronics) .....................  Via sensor power supply

Incorrect Polarity Protection

System interface ................................................. yes
Digital input yes
Digital output yes
Actuator ............................................................... power supply UA yes
Sensor ................................................................. power supply US yes

Outputs

Quantity ...............................................................   8
Polarity ................................................................   PNP
Voltage ............................................................... 24 VDC
Nominal current 2 A per channel
Overvoltage protection Yes (diode)
Max. switching frequency at ohmic load ............. 50 Hz
Max. switching frequency at inductive load ........ 10 Hz
Short-circuit protection ........................................  Auto. Reset after short-circuit clearance

Inputs

Quantity ...............................................................   8
Polarity ................................................................   PNP
Input characteristic and switch threshold ............  EN 61131-2

Sensor Power Supply

Max. total current ................................................ 9 A (defined by 7/8“)
Supply for sensors .............................................. max. 200 mA for each sensor
Short-circuit protection for sensors ..................... Multifuse
............................................................................ up to 100 mA load automatic start-up
............................................................................ from 100 mA load reset required

Actuator supply

Max. total current ................................................ 9 A (defined by 7/8“)
Short-circuit protection ....................................... Reverse-connect protection

www.comoso.com

«
...
31
32
33
34
35
...
»

Summary of Contents for IMPACT67-P










































Reviews:

No comments

Related manuals for IMPACT67-P

Brand: Farris Engineering Pages: 12

Brand: Eastern Times Technology Pages: 4

Brand: Vacon Pages: 18

Brand: CAME Pages: 32

Brand: Aaeon Pages: 76

VARIVENT D Series

Brand: GEA Pages: 78

Brand: GEA Pages: 96

Brand: GEA Pages: 66

Brand: UNI Pages: 21

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Brand: Kamstrup Pages: 36

Brand: JFA Electronicos Pages: 29

Brand: Unitech Pages: 55

Brand: S&C Pages: 8

Brand: Ublox Pages: 2

Brand: u-blox Pages: 19

Brand: Vacon Pages: 50

Brand: V2 Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands