Murr Elektronik IMPACT67-P Instruction Manual Download Page 35 | Manualshive

Page: 35 / 41

background image

IMPACT67-P manual

34

V

1.6

5.3 IMPACT67-P DO8

Technical data

Number of outputs .............................................. 8
Operating voltage of actuator power supply  ...... 24 V ± 25% (18 V to 30.2 V) DC
Operating voltage of sensor power supply  ........ 24 V ± 25% (18 V to 30.2 V) DC
Power supply (module electronics) .....................  Via sensor power supply

Incorrect Polarity Protection

System interface .................................................  yes
Digital output yes
Actuator  .............................................................. power supply UA yes
Sensor  ................................................................ power supply US yes

Outputs

Quantity ...............................................................   8
Polarity ................................................................   PNP
Voltage ............................................................... 24 VDC
Nominal current 2 A per channel
Overvoltage protection Yes (diode)
Max. switching frequency at ohmic load ............. 50 Hz
Max. switching frequency at inductive load ........ 10 Hz
Short-circuit protection ........................................  Auto. Reset after short-circuit clearance

Actuator supply

Max. total current ................................................ 9 A (defined by 7/8“)
Short-circuit protection ....................................... Reverse-connect protection

Profibus

Baud rates ...........................................................  9.6 KBaud to 12 MBaud
............................................................................  31.25 KBaud is not supported
Protocol ...............................................................   Profibus DP to IEC 61158/61784
Operating modes  ............................................... Sync Mode and Freeze Mode are supported
ID number ...........................................................  3101 h
Profibus address .................................................  0-99 set by rotary switches
Galvanic isolation  ............................................... Between  bus  and  module electronics

www.comoso.com

«
...
33
34
35
36
37
...
»

Summary of Contents for IMPACT67-P










































Reviews:

No comments

Related manuals for IMPACT67-P

Brand: NEC Pages: 149

Brand: NEC Pages: 13

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 20

Brand: GARAN Pages: 8

Brand: Gamma Vacuum Pages: 25

Brand: Gamma Pages: 28

Brand: S&P Pages: 12

Brand: S&C Pages: 34

Brand: S&C Pages: 32

IntelliCap Plus

Brand: S&C Pages: 32

Brand: S&P Pages: 12

Brand: S&C Pages: 35

Brand: Yamaha Pages: 5

Brand: Yamaha Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands