Murr Elektronik IMPACT67-P Instruction Manual Download Page 36 | Manualshive

Page: 36 / 41

background image

V 1.6

35

5.4 IMPACT67 DO16

Technical data

Number of outputs .............................................. 16
Operating voltage of actuator power supply  ...... 24 V ± 25% (18 V to 30.2 V) DC
Operating voltage of sensor power supply  ........ 24 V ± 25% (18 V to 30.2 V) DC
Power supply (module electronics) ....................  Via sensor power supply

Incorrect Polarity Protection

System interface .................................................  yes
Digital output yes
Actuator  ............................................................. power supply UA yes
Sensor power supply US ....................................  yes

Outputs

Quantity .............................................................. 16
Polarity ................................................................ PNP
Voltage .............................................................. 24 VDC
Nominal current 0.5 A per channel
Overvoltage protection Yes (diode)
Max. switching frequency at ohmic load ............ 50 Hz
Max. switching frequency at inductive load ........ 10 Hz
Short-circuit protection ....................................... Auto. Reset after short-circuit clearance

Actuator supply

Max. total current ................................................ 9 A (defined by 7/8“)
Short-circuit protection ...................................... Reverse-connect protection

Profibus

Baud rates ..........................................................  9.6 KBaud to 12 MBaud
............................................................................  31.25 KBaud is not supported
Protocol ..............................................................  Profibus DP to IEC 61158/61784
Operating modes  ............................................... Sync Mode and Freeze Mode are supported
ID number ...........................................................  3101 h
Profibus address.................................................  0-99 set by rotary switches
Galvanic isolation  .............................................. Between bus and module electronics

www.comoso.com

«
...
34
35
36
37
38
...
»

Summary of Contents for IMPACT67-P










































Reviews:

No comments

Related manuals for IMPACT67-P

Brand: CAME Pages: 12

Brand: CAME Pages: 16

Brand: Ultrak Pages: 41

Brand: Zander Aachen Pages: 10

Brand: Panamax Pages: 16

Brand: VAT Pages: 26

Brand: Eaton Pages: 8

Brand: ABB Pages: 44

Brand: Omega Pages: 2

Brand: Zmotion Pages: 34

Brand: Telit Wireless Solutions Pages: 45

Brand: YOKOGAWA Pages: 33

Brand: Yoshitake Pages: 18

Brand: Variotech Pages: 24

Brand: Stramatel Pages: 10

Brand: Heat Controller Pages: 10

Brand: PI Pages: 6

Brand: Yale Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands