Murphy Selectronic TTD Series Installation And Operation Manual Download Page 3

Page: 3 / 58

Table of Contents

Product Description................................................................................................................ 1

Display Head (TTD-H)..................................................................................................1

Power and Control Inputs/Outputs (PSU-2) .................................................................2

Installation ............................................................................................................................... 3

Installation Diagram for the TTD Display......................................................................3

Typical Installations for TTD Power and Control Inputs/Outputs ..................................5

TTD G-Lead Choke Installation Instruction ..................................................................8

Backup Battery Replacement.......................................................................................9

Product Features................................................................................................................... 11

The Display ................................................................................................................12

Front Panel Key Functionality ....................................................................................13

TTD Keypad Features ................................................................................................13

Operational Display Messages...................................................................................17

Backlight used as Status Indication............................................................................19

Configuration / Setup of the TTD Annunciator .................................................................. 20

Navigating the TTD Front Panel.................................................................................20

Entering Setup Mode .................................................................................................21

Setup 1 – Timer Setup ...............................................................................................23

Setup 2 – Sensor Mode .............................................................................................25

Setup 3 – Sensor Type ..............................................................................................28

Setup 4 – Remote Reset Remote Lockout Select and No-Flow Enable Delay...........30

Setup 5 - Hourmeters .................................................................................................32

Setup 6 – Speed Calibration ......................................................................................33

Setup 7 – Tachometer Overspeed Option..................................................................34

Setup 8 – Tachometer Underspeed Option................................................................35

Setup 9 – Communication Settings ............................................................................36

Setup A – Output Mode..............................................................................................37

Setup B – Unit Identification (ID) ................................................................................38

Setup C – Factory Default ..........................................................................................39

To order call 1-800-548-1191 or visit www.partdeal.com - [email protected]

Summary of Contents for Selectronic TTD Series



























































Search results

Summary of Contents for Selectronic TTD Series

Reviews:

Related manuals for Selectronic TTD Series

Brands by name

Popular brands

Murphy Selectronic TTD Series, Installation And Operation Manual

Search results

Summary of Contents for Selectronic TTD Series

Reviews:

Related manuals for Selectronic TTD Series

Brands by name

Popular brands