manualshive.com logo in svg

Murphy Selectronic TTD Series, Installation And Operation Manual, Page: 16 / 58

Share
Download
Murphy Selectronic TTD Series Installation And Operation Manual Download Page 16

 

Section 50 

 

00-02-0329 

01-09-07 - 

12 -

 

The Display 

The TTD annunciator features a static LCD display (A) with backlight (external DC is required). 
The operating temperature is between -40° to 85°C. The applicable icon and number (B, C and 
D) will be displayed to clarify the display readings or alert the operator to an operating 
condition. 

 

Display Icons 

•

 

RUN

 – run mode 

•

 

RPM

 – screen value 

•

 

HOURS

 – screen value 

•

 

TYPE

 – channel type configuration 

•

 

LOW BATT 

– low battery warning (displayed if the condition exists) 

•

 

HISTORY

 – alarm or shutdown history 

•

 

TEST

 – test mode 

•

 

LUBE

 – pre-lubrication timer 

•

 

POSTLUBE

 – post-lubrication timer 

•

 

SHUTDOWN

 – stop mode 

•

 

ALARM

 – alarm(s) warning (displayed if the condition exists) 

•

 

SETPOINT

 – edit set-point value 

•

 

SETUP

 – setup menu(s) 

To order call 1-800-548-1191 or visit www.partdeal.com - [email protected]

Summary of Contents for Selectronic TTD Series



























































Reviews:

No comments