manualshive.com logo in svg

Murphy Selectronic TTD Series, Installation And Operation Manual, Page: 23 / 58

Share
Download
Murphy Selectronic TTD Series Installation And Operation Manual Download Page 23

 

Section 50 

 

00-02-0329 

01-09-07 - 

19 -

 

Fault Codes 

Fault Codes 

Description 

1-48

 

Indicates the input that has faulted or alarmed 

49 

Loss of Ignition (When the CD ignition falls below 90 VDC

±

 10%, 

the firmware activates the fault) 

50 

Overspeed 

51 

Underspeed 

52 

Manual Stop 

53 

Low Device Voltage (internal diagnostic) 

54 

Crystal Failure (internal diagnostic) 

60 

Watchdog Timer 

61 

Loss of SPI Link 

62 

Low DC Voltage (Alarm) 

63 

Low Backup Battery (Alarm) 

 

Backlight used as Status Indication 

If AC or DC power is connected the backlight functionality is implemented on Div. 2 power 
supplies. 

Run Mode

 – The backlight will be yellow under this condition. 

Shutdown Mode

 – The backlight will turn red under this condition. When a shutdown fault is 

detected, the backlight will blink. The backlight blinking will continue for 5 minutes, and can be 
aborted if the user presses any key.  After 5 minutes, the backlight stays red. During manual 
shutdown sequence the backlight will be red. 

To order call 1-800-548-1191 or visit www.partdeal.com - [email protected]

Summary of Contents for Selectronic TTD Series



























































Reviews:

No comments