manualshive.com logo in svg

Murphy Selectronic TTD Series, Installation And Operation Manual, Page: 20 / 58

Share
Download
Murphy Selectronic TTD Series Installation And Operation Manual Download Page 20

 

Section 50 

 

00-02-0329 

01-09-07 - 

16 -

 

Setup Mode – Menus 

The condition on the display indicates the 

RUN

 and 

SHUTDOWN

 icons may be on. 

 

Key 

Function 

Setup/Enter

 

If the unit is in SETUP 0, pressing [ENTER] exits the unit from the 
Setup Mode.  If the unit is in any other Setup, pressing [ENTER] 
accesses the sub-menu for that Setup. 

Up Arrow 

Press [UP ARROW} to navigate to the next menu. 

Down Arrow 

Press [DOWN ARROW} to navigate to the previous menu. 

Reset/ESC 

Press [ESC] to exit from the Setup Menu and return to the 
operational display for the current mode. 

Stop 

If the system is in Run Mode, pressing and holding the [STOP] 
key for 2 seconds will begin the Shutdown sequence. 

 

Setup Mode – Edit Settings 

The condition on the display indicates the 

SETUP

 icon shows, and either the 

RUN

 or 

SHUTDOWN

 icons may show. 

 

Key 

Function 

Setup/Enter

 

Press [ENTER] to exit or advance a Setup menu and save 
changes. 

Up Arrow 

Press [UP ARROW} to increment the value to the maximum 
range.  Holding the key accelerates the incrementing action. 

Down Arrow 

Press [DOWN ARROW} to decrement the value to the minimum 
range.  Holding the key accelerates the decrementing action. 

Reset/ESC 

Press [ESC] to exit or advance the Setup Menu without saving 
your changes. 

Stop 

If the system is in Run Mode, pressing and holding the [STOP] 
key for 2 seconds will begin the Shutdown sequence. 

 

To order call 1-800-548-1191 or visit www.partdeal.com - [email protected]

Summary of Contents for Selectronic TTD Series



























































Reviews:

No comments