manualshive.com logo in svg

MTU MS150033/05E, Operating Instructions Manual

Share
Download
MTU MS150033/05E Operating Instructions Manual Download Page 86

152042 – Open Primary, Channel 17

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not
discharged.

1. Check cabling to ignition coil.
2. Check ignition coil.

152043 – Open Primary, Channel 18

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not
discharged.

1. Check cabling to ignition coil.
2. Check ignition coil.

152044 – Open Primary, Channel 19

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not
discharged.

1. Check cabling to ignition coil.
2. Check ignition coil.

152045 – Open Primary, Channel 20

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not
discharged.

1. Check cabling to ignition coil.
2. Check ignition coil.

152050 – Warn. Missing Ring Gear Signal

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Crankshaft signal 182 teeth is
missing.

u

Check sensor B13.2, check sensor clearance and cabling,
replace if necessary.

152051 – Warning Missing Reset Signal

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Reset signal from crankshaft is
missing.

u

Check sensor B75, check sensor clearance and cabling, replace
if necessary.

152052 – Warn. Missing Camshaft Signal

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Missing camshaft signal for
ignition system.

u

Check sensor B1.2, check sensor clearance and cabling,
replace if necessary.

86 | Troubleshooting | MS150033/05E 2013-10

TIM-ID: 0000017543 - 001

Summary of Contents for MS150033/05E






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands