manualshive.com logo in svg

MTU MS150033/05E, Operating Instructions Manual

Share
Download
MTU MS150033/05E Operating Instructions Manual Download Page 106

5.3 Engine governor – Fault messages

015 – LO P-Lube Oil

ZKP-Number: 

Yellow alarm.
Associated parameter 2.0100.921

Cause

Corrective action

Engine oil pressure too low (limit
value 1). Lack of engine oil,
engine speed too low, oil lines,
oil heat exchanger clogged, oil
pump defective.

1. Check oil system, oil heat exchanger.
2. Replace oil filter (→ Page 165).
3. Take oil sample and analyze (→ Page 164).

016 – SS P-Lube Oil

ZKP-Number: 

Red alarm. Engine shutdown.
Associated parameter 2.0100.922

Cause

Corrective action

Engine oil pressure too low (limit
value 2). Lack of engine oil,
engine speed too low, oil lines,
oil heat exchanger clogged, oil
pump defective.

1. Check oil system, oil heat exchanger.
2. Replace oil filter (→ Page 165).
3. Take oil sample and analyze (→ Page 164).

019 – HI T-Exhaust A

ZKP-Number: 

Yellow alarm.
Associated parameter 2.0126.931

Cause

Corrective action

Exhaust gas temperature (A
side) after turbine too high (limit
value 1). Incorrect ignition
timing, mixture too lean or too
rich, damage to turbine.

1. Check exhaust turbocharger.
2. Check ignition timing (→ Page 149).
3. Check mixture setting.
4. Check spark plugs.

106 | Troubleshooting | MS150033/05E 2013-10

TIM-ID: 0000017544 - 001

Summary of Contents for MS150033/05E






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands