manualshive.com logo in svg

MTU MS150033/05E, Operating Instructions Manual

Share
Download
MTU MS150033/05E Operating Instructions Manual Download Page 133

552 – AL GasControlCheck Fault

ZKP-Number: 

Red alarm.
Associated parameter 2.1090.118

Cause

Corrective action

Gas train test was not
successful. Alarm is activated if
the gas train does not report OK
within a specified time-out
period. Either the gas train leak
test was not successful, the
time-out period is set too short,
or communication is faulty.

1. Check gas train.
2. Check cabling.

554 – AL Ignition Fault

ZKP-Number: 

Red alarm.
Associated parameter 2.1090.122

Cause

Corrective action

Ignition failure. Alarm is
activated if the feedback signal
from ignition system is not
received within a specified time-
out period. Either the ignition
could not be activated, the time-
out period is set too short, or
communication is faulty.

u

Check ignition system and cabling.

556 – AL GasValve Fault

ZKP-Number: 

Red alarm.
Associated parameter 2.1090.124

Cause

Corrective action

Gas supply solenoid valve faulty.
Either the gas supply solenoid
valves are faulty, the time-out
period is set too short, or
communication is faulty.

u

Check gas train and cabling.

MS150033/05E 2013-10

| Troubleshooting | 133

TIM-ID: 0000017544 - 001

Summary of Contents for MS150033/05E






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands