manualshive.com logo in svg

MTU MS150033/05E, Operating Instructions Manual

Share
Download
MTU MS150033/05E Operating Instructions Manual Download Page 85

152035 – Open Primary, Channel 10

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not
discharged.

1. Check cabling to ignition coil.
2. Check ignition coil.

152036 – Open Primary, Channel 11

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not
discharged.

1. Check cabling to ignition coil.
2. Check ignition coil.

152037 – Open Primary, Channel 12

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not
discharged.

1. Check cabling to ignition coil.
2. Check ignition coil.

152038 – Open Primary, Channel 13

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not
discharged.

1. Check cabling to ignition coil.
2. Check ignition coil.

152039 – Open Primary, Channel 14

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not
discharged.

1. Check cabling to ignition coil.
2. Check ignition coil.

152040 – Open Primary, Channel 15

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not
discharged.

1. Check cabling to ignition coil.
2. Check ignition coil.

152041 – Open Primary, Channel 16

Yellow alarm. Initiated by IC922.

Cause

Corrective action

Ignition energy was not
discharged.

1. Check cabling to ignition coil.
2. Check ignition coil.

MS150033/05E 2013-10

| Troubleshooting | 85

TIM-ID: 0000017543 - 001

Summary of Contents for MS150033/05E






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands