manualshive.com logo in svg

MTU MS150033/05E, Operating Instructions Manual

Share
Download
MTU MS150033/05E Operating Instructions Manual Download Page 139

6.2 Crankcase Breather

6.2.1 Oil separator – Filter replacement

Preconditions

☑

Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Filter element

(→ Spare Parts Catalog)

Sealing ring

(→ Spare Parts Catalog)

O-ring

(→ Spare Parts Catalog)

O-ring

(→ Spare Parts Catalog)

WARNING

Hot oil.
Oil can contain combustion residues which are harmful to health.

Risk of injury and poisoning!

• Wear protective clothing, gloves, and goggles / safety mask.
• Avoid contact with skin.
• Do not inhale oil vapor.

WARNING

Oils/oil vapors are combustible/explosive.

Risk of fire and explosion!

• Avoid open flames, electric sparks and ignition sources.
• Do not smoke.

Oil separator – Filter replace-
ment

1.

Release clamp (2) on both sides and re-
move it.

2.

Remove housing cover (1).

MS150033/05E 2013-10

| Task Description | 139

TIM-ID: 0000029127 - 004

Summary of Contents for MS150033/05E






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands