MTU 12 V 4000 L62FB Operating Instructions Manual Download Page 54

Page: 54 / 181

112309 – HI T-Exhaust A9

Yellow alarm. Initiated by EMU.

Cause

Corrective action

Individual exhaust gas
temperature of this cylinder is too
high in comparison with weighted
average.

1. Check emission values.
2. Check ignition timing (→ Page 140).
3. Check valve drive (exhaust valves do not close).

112310 – HI T-Exhaust A10

Yellow alarm. Initiated by EMU.

Cause

Corrective action

Individual exhaust gas
temperature of this cylinder is too
high in comparison with weighted
average.

1. Check emission values.
2. Check ignition timing (→ Page 140).
3. Check valve drive (exhaust valves do not close).

112311 – HI T-Exhaust B1

Yellow alarm. Initiated by EMU.

Cause

Corrective action

Individual exhaust gas
temperature of this cylinder is too
high in comparison with weighted
average.

1. Check emission values.
2. Check ignition timing (→ Page 140).
3. Check valve drive (exhaust valves do not close).

112312 – HI T-Exhaust B2

Yellow alarm. Initiated by EMU.

Cause

Corrective action

Individual exhaust gas
temperature of this cylinder is too
high in comparison with weighted
average.

1. Check emission values.
2. Check ignition timing (→ Page 140).
3. Check valve drive (exhaust valves do not close).

112313 – HI T-Exhaust B3

Yellow alarm. Initiated by EMU.

Cause

Corrective action

Individual exhaust gas
temperature of this cylinder is too
high in comparison with weighted
average.

1. Check emission values.
2. Check ignition timing (→ Page 140).
3. Check valve drive (exhaust valves do not close).

54 | Troubleshooting | MS150098/02E 2016-11

TIM-ID: 0000027854 - 001

Summary of Contents for 12 V 4000 L62FB






















































































































































































Search results

Summary of Contents for 12 V 4000 L62FB

Reviews:

Related manuals for 12 V 4000 L62FB

Brands by name

Popular brands

MTU 12 V 4000 L62FB, Operating Instructions Manual

Search results

Summary of Contents for 12 V 4000 L62FB

Reviews:

Related manuals for 12 V 4000 L62FB

Brands by name

Popular brands