MTU 12 V 4000 L62FB Operating Instructions Manual Download Page 94

Page: 94 / 181

030 – SS Engine Overspeed

Red alarm. Engine shutdown.

Associated parameter 2.2510.932

Cause

Corrective action

Overspeed detected by ECU. This
usually fault message usually
follows other fault messages.
Check of governor, throttle
closing position

1. Check governor.
2. Check throttle closing position.

031 – HI ETC1 Overspeed

Yellow alarm.

Associated parameter 2.3011.931

Cause

Corrective action

Speed of primary turbocharger
too high (limit value 1).

Turbocharger speed sensor is not fitted at present. Check ECU
setting for this input.

032 – SS ETC1 Overspeed

Red alarm. Engine shutdown.

Associated parameter 2.3012.932

Cause

Corrective action

Speed of primary turbocharger
too high (limit value 2).

Turbocharger speed sensor is not fitted at present. Check ECU
setting for this input.

036 – HI ETC2 Overspeed

Yellow alarm.

Associated parameter 2.3013.931

Cause

Corrective action

Speed of 1st secondary
turbocharger too high (limit value
1).

Turbocharger speed sensor is not fitted at present. Check ECU
setting for this input.

037 – SS ETC2 Overspeed

Red alarm. Engine shutdown.

Associated parameter 2.3013.912

Cause

Corrective action

Speed of 1st secondary
turbocharger too high (limit value
2).

Turbocharger speed sensor is not fitted at present. Check ECU
setting for this input.

94 | Troubleshooting | MS150098/02E 2016-11

TIM-ID: 0000027858 - 001

Summary of Contents for 12 V 4000 L62FB






















































































































































































Search results

Summary of Contents for 12 V 4000 L62FB

Reviews:

Related manuals for 12 V 4000 L62FB

Brands by name

Popular brands

MTU 12 V 4000 L62FB, Operating Instructions Manual

Search results

Summary of Contents for 12 V 4000 L62FB

Reviews:

Related manuals for 12 V 4000 L62FB

Brands by name

Popular brands