MTU 12 V 4000 L62FB Operating Instructions Manual Download Page 157

Page: 157 / 181

7.9 Coolant Circuit, General, High-Temperature Circuit

7.9.1 Engine coolant – Level check

Preconditions

☑

Engine is stopped and starting disabled.

☑

MTU Fluids and Lubricants Specifications (A001061/..) are available.

WARNING

Coolant is hot and under pressure.
Risk of injury and scalding!
• Let the engine cool down.
• Wear protective clothing, gloves, and goggles / safety mask.

Engine coolant – Level check

Read off system filling pressure for fuel-optimized engine (→ Page 27) on pressure gage.

Top up with treated coolant as necessary (→ Page 161).

MS150098/02E 2016-11

| Coolant Circuit, General, High-Temperature Circuit | 157

TIM-ID: 0000045244 - 001

Summary of Contents for 12 V 4000 L62FB






















































































































































































Search results

Summary of Contents for 12 V 4000 L62FB

Reviews:

Related manuals for 12 V 4000 L62FB

Brands by name

Popular brands

MTU 12 V 4000 L62FB, Operating Instructions Manual

Search results

Summary of Contents for 12 V 4000 L62FB

Reviews:

Related manuals for 12 V 4000 L62FB

Brands by name

Popular brands