Mitsubishi MELSEC-A AJ65VBTCU-68DAVN User Manual Download

Page: 52 / 104

4 - 13 4 - 13

MELSEC-A

4 SETUP AND PREPARATION BEFORE OPERATION

POINT

• On this unit, use the Ver. 1.10-compatible CC-Link dedicated cable (FANC-

110SBH, CS-110, FA-CBL200PSBH).
You cannot use the Ver. 1.10-compatible CC-Link dedicated cables of other than
the above types, CC-Link dedicated cables and CC-Link dedicated, high-
performance cables.

• The shield cable of the CC-Link dedicated cable should be connected to "SLD" in

each module, and both ends should be grounded through "FG".
SLD and FG are connected inside the module.

4.8.3 How to connect connectors

The following shows how to connect the one-touch connectors and online connectors.

One-touch connector
plug for communication
(A6CON-L5P)

One-touch connector plug for power supply/FG
(A6CON-PW5P/A6CON-PW5P-SOD)

Online connector for power supply/FG
(A6CON-PWJ5P)

Online connector
for communication
(A6CON-LJ5P)

Summary of Contents for MELSEC-A AJ65VBTCU-68DAVN









































































































Search results

Summary of Contents for MELSEC-A AJ65VBTCU-68DAVN

Reviews:

Related manuals for MELSEC-A AJ65VBTCU-68DAVN

Brands by name

Popular brands

Mitsubishi MELSEC-A AJ65VBTCU-68DAVN, User Manual

Search results

Summary of Contents for MELSEC-A AJ65VBTCU-68DAVN

Reviews:

Related manuals for MELSEC-A AJ65VBTCU-68DAVN

Brands by name

Popular brands