Mitsubishi MELSEC-A AJ65VBTCU-68DAVN User Manual Download | Manualshive

Page: 94 / 104

background image

6 - 3 6 - 3

MELSEC-A

6 TROUBLESHOOTING

(3) When the AJ65VBTCU-68DAVN "RUN" LED is off

Check item

Corrective action

Is an attempt made to perform operation in the
normal mode with the mode select switch set in the
test mode?

Switch power on again after setting the mode select
switch to the normal mode.

Has the watchdog timer error occurred?

Using the link special registers (SW0084 to
SW0087) of the master module, check the
watchdog timer error and power on the
AJ65VBTCU-68DAVN again.
If the "RUN" LED is not lit after power is switched
on again, the possible cause is a hardware fault.
Contact your nearest Mitsubishi representative.

(4) When the AJ65VBTCU-68DAVN "L RUN" LED is off

Communications are broken.
For details, refer to troubleshooting in the user's manual of the master module
used.

(5) When the AJ65VBTCU-68DAVN "L ERR." LED flickers at fixed intervals

Check item

Corrective action

Has the station number or transmission speed
setting switch position been changed during normal
operation?

After correcting the setting switch setting, switch
power on again.

Is the station number or transmission speed setting
switch faulty?

If the "L ERR." LED has begun flickering though
switch setting change was not made during
operation, the possible cause is a hardware fault.
Contact your nearest Mitsubishi representative.

(6) When the AJ65VBTCU-68DAVN "L ERR." LED flickers at unfixed intervals

Check item

Corrective action

Have you forgotten fitting the terminating resistor?

Check whether the terminating resistor is fitted. If it
is not connected, connect it and switch power on
again.

Is the module or CC-Link dedicated cable affected
by noise?

Earth both ends of the shield wire of the CC-Link
dedicated cable to the protective earth conductor
via SLD and FG of the corresponding module.
Earth the FG terminal of the module without fail.
When carrying out wiring in piping, earth the pipe
without fail.

(7) When the AJ65VBTCU-68DAVN "L ERR." LED is on

Check item

Corrective action

Are the station number and transmission speed
correct?

Set the correct station number and transmission
speed.

«
...
92
93
94
95
96
...
»

Summary of Contents for MELSEC-A AJ65VBTCU-68DAVN









































































































Reviews:

No comments

Related manuals for MELSEC-A AJ65VBTCU-68DAVN

VLT Micro Drive FC 51 Series

Brand: Danfoss Pages: 28

VLT Micro Drive FC 51 Series

Brand: Danfoss Pages: 73

VLT AutomationDrive FC 300

Brand: Danfoss Pages: 4

VLT AutomationDrive

Brand: Danfoss Pages: 89

Brand: µ-Dimension Pages: 6

Brand: KROHNE Pages: 67

PX348 PxArt Audio

Brand: PXM Pages: 25

Brand: Datavideo Pages: 13

Brand: Patton electronics Pages: 10

Brand: Cobra Pages: 14

Brand: mundoclima Pages: 60

Brand: Lindy Pages: 14

AZZYRRO 3-6-ZSS-HP

Brand: ZCS Pages: 65

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology 8R

Brand: M-Audio Pages: 25

Single Phase Series

Brand: Zeus Appollo Pages: 12

Brand: Photosonix Pages: 12

Brand: Fronius Pages: 92

Brand: Metrodata Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands