Mitsubishi Electric MUY-GL09NA-U1 Service Manual Download Page 69

Page: 69 / 76

11-2. MUZ-GL18NA MUZ-GL18NAH MUY-GL18NA

NOTE:

Turn OFF the power supply before disassembly.

OPERATING PROCEDURE

PHOTOS/FIGURES

1. Removing the cabinet

(1) Remove the screws of the service panel.

(2) Remove the screws of the top panel.

(3) Remove the screw of the valve cover.

(4) Remove the service panel.

(5) Remove the screws fixing the conduit cover.

(6) Remove the conduit cover.

(7) Remove the screw of fixing the conduit plate.

(8) Remove the conduit plate.

(9) Remove the top panel.

(10) Remove the valve cover.

(11) Disconnect the power supply and indoor/outdoor connect-

ing wire.

(12) Remove the screws of the cabinet.

(13) Remove the cabinet.

(14) Remove the screws of the back panel.

(15) Remove the back panel.

Photo 3

Photo 4

Photo 1

Photo 2

Screws of the cabinet

Screws of the top panel

Screw of the back panel

Screws of the cabinet

Screws of

the cabinet

Screws of the service panel

Screw of

the valve

cover

Screws of

the cabinet

Screws of

the back

panel

Screws

of the

cabinet

Screws of the conduit cover

Screw of the conduit plate

OBH733G

Summary of Contents for MUY-GL09NA-U1













































































Search results

Summary of Contents for MUY-GL09NA-U1

Reviews:

Related manuals for MUY-GL09NA-U1

Brands by name

Popular brands

Mitsubishi Electric MUY-GL09NA-U1, Service Manual

Search results

Summary of Contents for MUY-GL09NA-U1

Reviews:

Related manuals for MUY-GL09NA-U1

Brands by name

Popular brands