Mitsubishi Electric MUY-GL09NA-U1 Service Manual Download Page 72

Page: 72 / 76

11-3. MUZ-GL24NA MUZ-GL24NAH MUY-GL24NA

NOTE

: Turn OFF the power supply before disassembly.

OPERATING PROCEDURE

PHOTOS/FIGURES

1. Removing the cabinet

(1) Remove the screws of the service panel.

(2) Remove the screws of the top panel.

(3) Remove the screw of the valve cover.

(4) Remove the service panel.

(5) Remove the screws fixing the conduit cover.

(6) Remove the conduit cover.

(7) Remove the top panel.

(8) Remove the valve cover.

(9) Disconnect the power supply and indoor/outdoor con-

necting wire.

(10) Remove the screws of the cabinet.

(11) Remove the cabinet.

(12) Remove the screws of the back panel.

(13) Remove the back panel.

Photo 2

Photo 1

Photo 3

Photo 4

Screws of the

top panel

Screws of the

back panel

Screws of

the service

panel

Screws of

the back

panel

Screws

of the

cabinet

Screws of the

back panel

Screws of

the back

panel

Screws of the

back panel

Screw of

the valve

cover

Screws of the

cabinet

Screws of the top panel

Screws of the

cabinet

Screws

of the

cabinet

Screws of the conduit cover

Screw of the conduit plate

OBH733G

Summary of Contents for MUY-GL09NA-U1













































































Search results

Summary of Contents for MUY-GL09NA-U1

Reviews:

Related manuals for MUY-GL09NA-U1

Brands by name

Popular brands

Mitsubishi Electric MUY-GL09NA-U1, Service Manual

Search results

Summary of Contents for MUY-GL09NA-U1

Reviews:

Related manuals for MUY-GL09NA-U1

Brands by name

Popular brands