Mitsubishi Electric MUY-GL09NA-U1 Service Manual Download Page 40

Page: 40 / 76

SERVICE FUNCTIONS

9-1. CHANGE IN DEFROST SETTING (MUZ)

Changing defrost finish temperature

<JS> To change the defrost finish temperature, cut/solder the JS wire of the outdoor inverter P.C. board (Refer to 10-6.1.).

Jumper

Defrost finish temperature

MUZ-GL09/12/15NA

MUZ-GL09/12/15NAH

MUZ-GL18/24NA

MUZ-GL18/24NAH

Soldered

(Initial setting)

41°F (5°C)

50°F (10°C)

None

(Cut)

50°F (10°C)

64°F (18°C)

9-2. PRE-HEAT CONTROL SETTING (MUZ)

MUZ-GL09/12/15/18

When moisture gets into the refrigerant cycle, it may interfere with the startup of the compressor at low outside tempera-

ture. The pre-heat control prevents this interference. The pre-heat control turns ON when the discharge temperature ther-

mistor is 68°F (20°C) or below. When the pre-heat control turns ON, the compressor is energized. (About 50 W)

MUZ-GL24

Prolonged low load operation, in which the thermostat is OFF for a long time, at low outside temperature [32°F (0°C) or

less] may cause the following troubles. The pre-heat control prevents those troubles.

1) If moisture gets into the refrigerant cycle and freezes, it may interfere the startup of the compressor.

2) If liquid refrigerant collects in the compressor, a failure in the compressor may occur.

The pre-heat control turns ON when the compressor temperature is 68°F (20°C) or below. When the pre-heat control

turns ON, the compressor is energized. (About 70 W)

Pre-heat control setting

<JK>

ON: To activate the pre-heat control, cut JK wire of the inverter P.C. board.

OFF: To deactivate the pre-heat control, solder JK wire of the inverter P.C. board.

(Refer to 10-6.1)

Jumper

Pre-heat control setting

MUZ-GL09/12/15/18NA

MUZ-GL09/12/15/18NAH

MUZ-GL24NA

MUZ-GL24NAH

Soldered

Deactivated

(Initial setting)

Deactivated

Cut

Activated

(Initial setting)

NOTE:

When the inverter P.C. board is replaced, check the JK wire, and cut/solder them if necessary.

MUZ-GL09NA MUZ-GL09NAH MUY-GL09NA

MUZ-GL12NA MUZ-GL12NAH MUY-GL12NA

MUZ-GL15NA MUZ-GL15NAH MUY-GL15NA

MUZ-GL18NA MUZ-GL18NAH MUY-GL18NA

MUZ-GL24NA MUZ-GL24NAH MUY-GL24NA

OBH733G

Summary of Contents for MUY-GL09NA-U1













































































Search results

Summary of Contents for MUY-GL09NA-U1

Reviews:

Related manuals for MUY-GL09NA-U1

Brands by name

Popular brands

Mitsubishi Electric MUY-GL09NA-U1, Service Manual

Search results

Summary of Contents for MUY-GL09NA-U1

Reviews:

Related manuals for MUY-GL09NA-U1

Brands by name

Popular brands