Mitsubishi Electric MUY-GL09NA-U1 Service Manual Download Page 2

Page: 2 / 76

TECHNICAL CHANGES

Use the specified refrigerant only

Never use any refrigerant other than that specified.

Doing so may cause a burst, an explosion, or fire when the unit is being used, serviced, or disposed of.

Correct refrigerant is specified in the manuals and on the spec labels provided with our products.

We will not be held responsible for mechanical failure, system malfunction, unit breakdown or accidents caused by

failure to follow the instructions.

Revision A:

• MUZ-GL12/15NA-

, MUZ-GL12/15NAH-

and MUY-GL09/12/15NA-

have been added.

MUZ-GL09NA

MUZ-GL09NAH

MUY-GL09NA

MUZ-GL09NA

MUZ-GL09NAH

MUZ-GL12NA

MUZ-GL12NAH

MUY-GL12NA

MUZ-GL15NA

MUZ-GL15NAH

MUY-GL15NA

MUZ-GL18NA

MUZ-GL18NAH

MUY-GL18NA

MUZ-GL24NA

MUZ-GL24NAH

MUY-GL24NA

1. New model

Revision B:

• MUZ-GL09NA-

and MUZ-GL09NAH-

have been added.

Revision C:

• MUZ-GL09NA-

and MUZ-GL09NAH-

have been added.

Revision D:

• MUZ-GL24NAH-

has been added.

Revision E:

• Capacity corrections have been corrected [7-1. 2), 3)].

Revision F:

• MUZ-GL24NA-

has been added.

Revision G:

• MUZ-GL09/12/15NA(H)-

and MUY-GL09/12/15NA-

have been added.

MUZ-GL09NA

MUZ-GL09NAH

1. Fan motor has been changed.

2. INVERTER P.C.BOARD has been changed.

3. EXPANSION VALVE has been changed.

4. 4-WAY VALVE has been changed.

5. R.V. COIL has been changed.

6. Compressor has been changed.

MUZ-GL12NA

MUZ-GL12NAH

1. Fan motor has been changed.

2. INVERTER P.C.BOARD has been changed.

3. EXPANSION VALVE has been changed.

4. 4-WAY VALVE has been changed.

5. R.V. COIL has been changed.

MUY-GL09NA

1. Fan motor has been changed.

2. INVERTER P.C.BOARD has been changed.

3. EXPANSION VALVE has been changed.

4. 4-WAY VALVE has been changed.

5. Compressor has been changed.

6. Refrigerant charge has been changed.

MUY-GL12NA

1. Fan motor has been changed.

2. INVERTER P.C.BOARD has been changed.

3. EXPANSION VALVE has been changed.

4. 4-WAY VALVE has been changed.

MUZ-GL15NA

MUZ-GL15NAH

MUY-GL15NA

1. Fan motor has been changed.

2. INVERTER P.C.BOARD has been changed.

3. EXPANSION VALVE has been changed.

OBH733G

Summary of Contents for MUY-GL09NA-U1













































































Search results

Summary of Contents for MUY-GL09NA-U1

Reviews:

Related manuals for MUY-GL09NA-U1

Brands by name

Popular brands

Mitsubishi Electric MUY-GL09NA-U1, Service Manual

Search results

Summary of Contents for MUY-GL09NA-U1

Reviews:

Related manuals for MUY-GL09NA-U1

Brands by name

Popular brands