manualshive.com logo in svg

MINOLTA-QMS magicolor 2300 DL, User Manual

Share
Download
MINOLTA-QMS magicolor 2300 DL User Manual Download Page 70

 Ordering Consumables

62

4

Press on the front handle of the OPC 
drum cartridge with one hand and hold 
the handle of the OPC protective cover 
with the other hand.

5

Peel the protective cover handle straight 
toward you.

"#

Dispose of it properly according to 
your local regulations.

6

Rotate the transfer belt release lever 
counterclockwise to its correct position 
(7 o’clock).

This lowers the transfer belt.

Attention

If the transfer belt release lever is not at its correct position 
(7 o’clock), the waste toner bottle cannot be installed.

7

Install a new waste toner bottle (see page 59).

"#

The printer must complete a 150-second calibration cycle after any 
consumable has been replaced. If you open the door before the 
message window reads 

IDLE/MAGICOLOR 2300DL

, the 

printer stops and repeats the calibration cycle.

Ordering Consumables

Choosing the right consumables for your printer not only increases its 
reliability and performance, but also minimizes the risk of damage. For 
example, only MINOLTA-QMS toner cartridges are designed to meet the 
exact specifications of your MINOLTA-QMS printer, giving maximum 
performance, efficiency, and long life. 
Toner cartridges and other consumables for your printer are available from 
your local vendor or Q-SHOP (www.q-shop.com). 
See the 

Service & Support Guide

 for a list of sources of service and support 

in the Americas. The most up-to-date worldwide information can be found at 
www.minolta-qms.com. 

Summary of Contents for magicolor 2300 DL













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands