manualshive.com logo in svg

MINOLTA-QMS magicolor 2300 DL, User Manual

Share
Download
MINOLTA-QMS magicolor 2300 DL User Manual Download Page 126

 Duplex Option

118

6

Attach the support wire for the duplex option to the printer.

a

Pull the right-side door release 
lever, and open the right-side 
door.

If you have lower feeder unit 
attached, you first need to open 
the lower right-side door.

b

Pull the tab for the support wire 
on the right side of the duplex 
option, and then hook the wire 
onto the hook of the printer.

c

Close the right-side door(s).

7

Reconnect interface cable.

8

Reconnect the power cord, and turn 
on the printer.

"#

In compliance with UL 
guidelines, “The appliance inlet 
is considered to be the main 
disconnect device.”

9

Check the configuration page from the 
control panel (Special Pages/Print 
Config Page menu) to verify the duplex option installation. 

10

Configure your driver for the new duplex option (see Chapter 4).

%

%

%

%

$

$

$

$

Summary of Contents for magicolor 2300 DL













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands