manualshive.com logo in svg

MINOLTA-QMS magicolor 2300 DL, User Manual

Share
Download
MINOLTA-QMS magicolor 2300 DL User Manual Download Page 100

 Solving Other Problems

92

Booklet Left 
and Right 
Binding 
output is 
incorrect.

Both the driver and 
the application have 
been set for collation.

For Booklet Left Binding and Booklet 
Right Binding, choose Collate only in 
the driver’s Paper Tab. Do not set 
collation in the application.

The printer 
pauses 
approxi- 
mately 90 
seconds.

The printer pauses 
for the color 
calibration procedure 
(also known as the 
Auto-Image Density 
Control [AIDC] cycle).

This process is 
provided to make 
sure reliable printer 
operation with 
optimum output 
quality. If you open 
the door before the 
display reads 

IDLE/

MAGICOLOR 
2300DL

, the printer 

stops and repeats the 
calibration cycle.

Wait while your printer automatically 
pauses to do an AIDC calibration cycle 
after 200 1-sided pages of a 
continuous print run.

The printer 
pauses 
approxi- 
mately 150 
seconds.

The printer pauses 
for the color 
calibration procedure 
(also known as the 
Auto-Image Density 
Control [AIDC] cycle).

This process is 
provided to make 
sure reliable printer 
operation with 
optimum output 
quality. If you open 
the door before the 
display reads 

IDLE/

MAGICOLOR 
2300DL

, the printer 

stops and repeats the 
calibration cycle.

Wait while your printer automatically 
pauses to do an AIDC calibration cycle 
after rebooting your printer when there 
has been an environmental change 
such as in temperature or humidity.
Wait while your printer automatically 
pauses to do an AIDC calibration cycle 
after “waking up” from ENERGY 
SAVER with more than 1,000 pages 
since the last AIDC cycle.
Wait while your printer automatically 
pauses to do an AIDC calibration cycle 
after the installation of a new toner 
cartridge or OPC drum.

Symptom

Cause

Solution

Summary of Contents for magicolor 2300 DL













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands