manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 2210, User Manual

Share
Download
MINOLTA-QMS MAGICOLOR 2210 User Manual Download Page 81

Solving Problems with Printing Quality 

79

There are 
toner 
smudges 
or residual 
images.

One or more of the toner 
cartridges is misinstalled 
or defective .

If the toner smudges are on only the 
front of the page:

„

Remove the toner cartridges and 
gently rock them five or six times to 
redistribute the toner. Then, reinstall 
the cartridges.

„

One or more toner cartridges may be 
defective. Check the toner car-
tridges. Install new ones, if neces-
sary. 

The image transfer roller 
need cleaning.

If toner smudges are on the front and 
back of the page:

„

Open the printer front cover once 
and close it again to clean the image 
transfer roller.

There are 
dark spots 
on the 
image.

The fuser oil roller is dirty 
or worn.

Remove the fuser oil roller and check 
the roller surface. If it is very dirty, 
replace it.

The transfer belt is 
defective.

Remove the transfer belt and check for 
damage. If necessary, replace it.

Symptom

Cause

Solution

Summary of Contents for MAGICOLOR 2210

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands