Miniature Aircraft USA X-Cell Whiplash Turbine Manual Download

Page: 28 / 38

Hardware for these

assemblies

Assembly Tip

• Install rubber grommets 135-104.

Through this grommets the fuel line

goes out of the frame, passes the

fan and goes inside again to the

pump.

• Install header tank using double

sided tape and hook & loop tape

to secure it. The center nipple is

connected to the engine fuel pump.

The right nipple (picture on the right

side) is connected to the main tank.

The left nipple is used to fuel the

tank system.

• Install tail boom assembly. Don’t

forget to use thread lock!

Turbine ECU

135-104

135-106

Hopper Tank

0078 x2

0016-2 x2

0087 x2

128-59

135-127 x2

0060-1 x3

0067 x2

135-128

0016-2 x 4

4mm Saftey Washer

0060-1 x 3

M3x6 Socket Bolt

0067 x 2

M3x10 Socket Bolt

0078 x 2

M4x12 Socket Bolt

0087 x 2

M4x20 Socket Bolt

Summary of Contents for X-Cell Whiplash Turbine







































Search results

Summary of Contents for X-Cell Whiplash Turbine

Reviews:

Related manuals for X-Cell Whiplash Turbine

Brands by name

Popular brands

Miniature Aircraft USA X-Cell Whiplash Turbine, Manual

Search results

Summary of Contents for X-Cell Whiplash Turbine

Reviews:

Related manuals for X-Cell Whiplash Turbine

Brands by name

Popular brands