Miniature Aircraft USA X-Cell Whiplash Turbine Manual Download

Page: 26 / 38

Rudder Servo

Hardware for these

assemblies

Use of a heavy duty

servo arm or wheel is

recommended on the

rudder servo.

14mm

0818-3

0059-7

131-148

0017-2

0116

Servo

Arm Not

Included

Assembly Tip

131-50

0017-2

0059-4

Servo

Arm Not

Included

131-148

0116

19mm

Use of heavy duty

servo arms is required

on the cyclic servos.

• Do not overtighten servo mount

screws. This will damage the rubber

dampers of the servos.

• Use high quality servo arms. Don’t

forget to use thread lock to secure

the balls 0116 and nuts 0017-2

Apply a small amount of

medium thread lock when

threading into metal parts

0059-4 x 4

M2.5x12 Socket Bolt

0017-2 x 2

2.5mm Hex Nut

0116 x 2

M2.5 Threaded Steel

Ball

0059-7 x 4

M2.5x20 Socket Bolt

Rear Cyclic

Servo

0059-1 x 4

M2.5x6 Socket Bolt

Summary of Contents for X-Cell Whiplash Turbine







































Search results

Summary of Contents for X-Cell Whiplash Turbine

Reviews:

Related manuals for X-Cell Whiplash Turbine

Brands by name

Popular brands

Miniature Aircraft USA X-Cell Whiplash Turbine, Manual

Search results

Summary of Contents for X-Cell Whiplash Turbine

Reviews:

Related manuals for X-Cell Whiplash Turbine

Brands by name

Popular brands