Miniature Aircraft USA X-Cell Whiplash Turbine Manual Download

Page: 27 / 38

Hardware for these

assemblies

Assembly Tip

0059-4 x 8

M2.5x10 Socket Bolt

0017-2 x 2

2.5mm Hex Nut

0116 x 2

M2.5 Threaded Steel

Ball

0061 x 4

M3x8 Socket Bolt

0059-4

131-148

0017-2

0116

Servo

Arm Not

Included

Cyclic Servo

• MA131-148 Servo Spacers are

included for proper servo linkage

alignment, if required.

• Install valves as shown
• Use adhesive velcro and hook &

loop tape to install pump

135-101 x4

0061 +

2700-01

0069 x4

0009 x4

0009 x 4

3mm small Washer

0069 x 4

M3x16 Socket Bolt

Pump

Apply a small amount of

medium thread lock when

threading into metal parts

• Install turbine supports (135-101).

The supports shall only ‘touch’

the engine. They shall not supply

pressure to the engine body.

2700-01 x 4

Blue M3 Washer

Summary of Contents for X-Cell Whiplash Turbine







































Search results

Summary of Contents for X-Cell Whiplash Turbine

Reviews:

Related manuals for X-Cell Whiplash Turbine

Brands by name

Popular brands

Miniature Aircraft USA X-Cell Whiplash Turbine, Manual

Search results

Summary of Contents for X-Cell Whiplash Turbine

Reviews:

Related manuals for X-Cell Whiplash Turbine

Brands by name

Popular brands