Miniature Aircraft USA X-Cell Whiplash Turbine Manual Download

Page: 20 / 38

131-20

Upper Main Shaft

Bearing Block

(Factory Assembled)

Middle Main Shaft

Bearing Block

(Factory Assembled)

Bottom Main Shaft

Bearing Block

(Factory Assembled)

NOTE: Middle bearing block features

threaded holes.

NOTE: Upper bearing block features

smooth, wrench access holes

Hardware for these

assemblies

Assembly Tip

• If using JR brand servos or other

“tall” servos, MA131-47 Servo Rail

Spacers are included for proper

servo linkage alignment, if required.

• Do not supply thread lock at screws

marked with a (*) at this assembly

step. They will be removed again

later.

Apply a small amount of

medium thread lock when

threading into metal parts

0060-1 x 11

M3x6 Socket Bolt
0061 x 8

M3x8 Socket Bolt

0064-3

131-19

0064-3

135-487

0004 x 2

4mm Washer

0063 x 3

M3x10 Socket Bolt

131-420

131-442

131-180

131-440

0225-5

0273

0273-05

131-180

0225-5

131-493

131-483

0078-4

131-441

131-19

0064-3

131-21

128-90

0078-4

0004

0060-1

0063

0061

2700-01

0032

0060-1

0032 x 2

M3 Self Tapping Screw

0078-4 x 2

M4x8 Socket Bolt

(*)

2700-01 x 4

Blue M3 Washer

Summary of Contents for X-Cell Whiplash Turbine







































Search results

Summary of Contents for X-Cell Whiplash Turbine

Reviews:

Related manuals for X-Cell Whiplash Turbine

Brands by name

Popular brands

Miniature Aircraft USA X-Cell Whiplash Turbine, Manual

Search results

Summary of Contents for X-Cell Whiplash Turbine

Reviews:

Related manuals for X-Cell Whiplash Turbine

Brands by name

Popular brands