Miniature Aircraft USA X-Cell Whiplash Turbine Manual Download

Page: 13 / 38

0064-3

0107

106-02

131-130-B

131-132-B

131-131

131-135

0012-2

Hardware for this

assembly

Assembly Tip

Hardware for this

assembly

Assembly Tips

• 3 piece thrust bearing (MA131-66)

outer race with larger I.D. (inside

diameter) installs closest to hub.

• Grease the center ball cage of the

thrust bearing. We recommend using

MA3200-06 Tri-Flow synthetic grease.

• Only hand tighten MA0061 Socket

Bolt until it is moderately tight. Do

not overtighten bolt or it may result

in fatigue to bolt. Use green thread

lock on these bolts.

0009

120-39

122-70

131-66

0071

0019

0107

120-39

131-112

131-64

0061

Small

I.D.

Large

I.D.

0159

Factory

Assembled

Factory

Assembled

Bearings

Factory Installed

in Blade Grips

• The use of a light oil such as

MA3200-02 Tri-Flow Oil is required

for tail rotor output shaft/pitch

slider lubrication

Apply oil to

output shaft

106-02

Apply a small amount of

medium thread lock when

threading into metal parts

0061 x 2

M3x8 Socket Bolt

0009 x 2

3mm Flat Steel Washer

0019 x 2

3mm Hex Nut

0071 x 2

M3x18 Socket Bolt

0107 x 2

M3x6 Threaded

Steel Ball

0073

0107 x 1

M3x6 Threaded

Steel Ball

0019 x 1

3mm Hex Nut

0064-3 x 2

M3x6 Button Head

Socket Bolt

0073 x 1

M3x20 Socket Bolt

0019

2-A-3

2-A-4

Note:

Blade grips will have some axial

play. This is normal.

Summary of Contents for X-Cell Whiplash Turbine







































Search results

Summary of Contents for X-Cell Whiplash Turbine

Reviews:

Related manuals for X-Cell Whiplash Turbine

Brands by name

Popular brands

Miniature Aircraft USA X-Cell Whiplash Turbine, Manual

Search results

Summary of Contents for X-Cell Whiplash Turbine

Reviews:

Related manuals for X-Cell Whiplash Turbine

Brands by name

Popular brands