Miniature Aircraft USA X-Cell Whiplash Turbine Manual Download

Page: 22 / 38

Hardware for these

assemblies

Assembly Tip

• Assemble main gear and crown

gear at the corresponding hubs.

• Install front drive assembly and

one way hub with main gear at the

frame and insert mainshaft with

collars.

• Push bottom bearing block up

and tighten screws. Take care that

it is aligned horizontal.

• Install jesus bolt, push crown

gear up and tighten jesus bolt.

• Then pull mainshaft to the top

and tighten upper collar.

• Check gear mesh of crown gear. If

it is too much then insert a 0620-

0x shim. If the play is too less,

remove one 0620-0x shim. At least

one shim has to be installed.

• Press bottom collar up and

tighten it.

Apply a small amount of

medium thread lock when

threading into metal parts

0088-3 x 5

M3x7 Tappered Bolt

0088 x 8

M3x8 Tappered Bolt

0059-2.5 x 8

M3x16 Socket Set

Screw

0088-3 x5

132-117-B

131-467

131-426

131-419

131-424

131-419

131-469-1

0088 x8

131-470

131-202

0021

0620-01, 0620-02,

0620-03 as required

131-466

0875

0059-2

0021

131-202

0059-2

0021 x 1

M4 Lock Nut

131-3

131-202 x 1

Jesus Bolt OWB

131-180

131-179

0183

131-411

131-10

105-70

131-428

131-419

131-413

Factory

Assembled

Factory

Assembled

Summary of Contents for X-Cell Whiplash Turbine







































Search results

Summary of Contents for X-Cell Whiplash Turbine

Reviews:

Related manuals for X-Cell Whiplash Turbine

Brands by name

Popular brands

Miniature Aircraft USA X-Cell Whiplash Turbine, Manual

Search results

Summary of Contents for X-Cell Whiplash Turbine

Reviews:

Related manuals for X-Cell Whiplash Turbine

Brands by name

Popular brands