Miniature Aircraft USA X-Cell Whiplash Turbine Manual Download

Page: 12 / 38

Hardware for this

assembly

Assembly Tip

• Make sure to include MA0273-1

Shim Washer between MA131-17-C

Output Gear and transmission case

bearing.

0051 x 2

M3x3 Socket Set

Screw

0056 x 2

M3x5 Dog Point

Socket Screw

0273 x 1

m6x10x.11” Steel

Shim Washer

0107 x 1

M3x6 Threaded

Steel Ball

Hardware for this

assembly

0273-1 x 1

m6x10x.004” Steel

Shim Washer

0225

0442

131-476

131-473

131-477

(left hand

thread)

131-474

0107

Factory

Assembled

2-A-1

Factory Assembled

Apply a small amount of

medium thread lock when

threading into metal parts

2-A-2

Factory Assembled

131-180

131-33

131-33-1

131-129

131-70

131-18-C

131-17-C

0215

0051

0237

0237-1

0056

Summary of Contents for X-Cell Whiplash Turbine







































Search results

Summary of Contents for X-Cell Whiplash Turbine

Reviews:

Related manuals for X-Cell Whiplash Turbine

Brands by name

Popular brands

Miniature Aircraft USA X-Cell Whiplash Turbine, Manual

Search results

Summary of Contents for X-Cell Whiplash Turbine

Reviews:

Related manuals for X-Cell Whiplash Turbine

Brands by name

Popular brands