manualshive.com logo in svg

Minebea MPC-201-25, Instruction Manual, Page: 11 / 124

Share
Download
Minebea MPC-201-25 Instruction Manual Download Page 11

 

 

IX

Date 

Manual No. 

Revision reason (details) 

July 2015 

DRW. No. 294-1697A 

Section 21-5: Changed "ERROR LED Illuminated" description. 
Added Section 21-6 "PC Personalization". 
Section 22-1: Added "Graph scale auto adjustment" item. 
Section 22-3: Standardized terminology and changed 
description. 
Added "Start trigger interrupt setting". 
Section 22-4: Added "Alarm record" and "Alarm output timing 
settings". 
Section 22-11: Changed graph scale setting description. 
Added Section 22-15 "ERROR LED Information Check 
Function" 

March 2016 

DRW. No. EN294-1697B

In accordance with ECN No. FN16-02015-B. 
APP Ver.1.300 and ROM Ver.1.100 or later   
Changed screen images following application version upgrade.
General correction of errors and standardization of terminology
Cover: Replaced product illustration with photograph. 
Section 5-3: Added note about software version. 
Section 8-1 (6): Added. (subsequent section numbering altered)
Section 8-2: Added note about condition changes. 
Section 9: Added note about setup file. 
Section 9-1-5: Added note about eject detection range. 
Section 9-2-1: Changed sensor label illustration and added 
100K to sensor capacity. 
Section 10-3-3: Added note about spreadsheet software. 
Section 12 (1): Added explanations for waveform data and 
numerical data. 
Section 22-4: Added explanation for data saving function. 
Section 23-1: Added LSMS-100K-S06 to analog specifications.

Jan. 2017 

DRW. No. EN294-1697C

In accordance with ECN No. FN16-02169 
Section 2: Added Windows 10 to the operating system. 

Aug. 2017 

DRW. No. EN294-1697D

In accordance with ECN FN17-02017 

・

Delete the company name in the contents. 

Dec. 2017 

DRW. No. 294-1697E 

In accordance with ECN No. FN17-02163B 
APP Ver.1.500 and ROM Ver.1.200 or later 
Changed screen images and product illustrations following 
application version upgrade and acquisition of CE marking. 
Cover: Replaced product photograph. 
Beginning, Section 1: Replaced dimensions diagram. 
Beginning, Sections 3, 5-2-5, 8-5: Added cross-reference to 
precautions. 
Beginning, Section 4: Compatible standards: Added standards 
and precautions. 

 

 

Summary of Contents for MPC-201-25





























































































































Reviews:

No comments