Minebea Intec Maxxis 5 Phase PR 5900/81 Operating Instructions Manual Download Page 44

Page: 44 / 94

Production lines

@admin

Production line

LP 1

enabled

Default

Load

Save

If a production line is deactivated, downloading to start related plans/plan lines/

recipes locally will not be possible. Recipes for non-activated production lines do not

appear in the menu [Plan]/[Recipe].

5.4.8

Local Control

In this menu item, you can conigure the parameters to start the [recipe]/[plan] on the

device.

Configuration

@admin

Inputs

Outputs

Modbus-TCP master

Limits

Parameters

Production lines

Local control

Overview weighing points

View weighing point

Simulation

2. Using the cursor, select and conirm the corresponding production line to activate

this for the device.

3. Press the [Default] soft key to return to the factory settings, if required.
4. Press the [Load] soft key in order to load the production line.

5. Finally, press the [Save] soft key to save the settings.

1. Select and conirm [Local control] using the cursor.

A selection window appears.

Phase PR 5900/81

5 Getting started

EN-42

Minebea Intec

Summary of Contents for Maxxis 5 Phase PR 5900/81































































































Search results

Summary of Contents for Maxxis 5 Phase PR 5900/81

Reviews:

Related manuals for Maxxis 5 Phase PR 5900/81

Brands by name

Popular brands

Minebea Intec Maxxis 5 Phase PR 5900/81, Operating Instructions Manual

Search results

Summary of Contents for Maxxis 5 Phase PR 5900/81

Reviews:

Related manuals for Maxxis 5 Phase PR 5900/81

Brands by name

Popular brands