Minebea Intec Maxxis 5 Phase PR 5900/81 Operating Instructions Manual Download Page 37

Page: 37 / 94

Phoenix Contact power supply (IB IL 24 PWR IN-PAC)

Phoenix Contact output module (IB IL 24 DO16-PAC)

They ofer a total of 8 digital inputs and a total of 52 digital outputs.

5.4.4.2

Coniguration tool

The modules must be conigured in terms of hardware according to the Phoenix

instructions. In addition, an IP address must be assigned to each terminal. Phoenix

provides the "IPAssign.exe" coniguration tool for that purpose.

5.4.4.3

Coniguration on the device

Configuration

@admin

Inputs

Outputs

Modbus-TCP master

Limits

Parameters

Production lines

Local control

Overview weighing points

View weighing point

Simulation

Modbus-TCP master

@admin

Communication error

ModBus-TCP module

Activate module

Show message

Phönix 1: 16IN:16OUT Not..

Default

Save

1. In the operating menu, select and conirm [Coniguration] - [ModBus-TCP master].

2. Select and conirm [Communication error].

A selection window opens.

5 Getting started

Phase PR 5900/81

Minebea Intec

EN-35

Summary of Contents for Maxxis 5 Phase PR 5900/81































































































Search results

Summary of Contents for Maxxis 5 Phase PR 5900/81

Reviews:

Related manuals for Maxxis 5 Phase PR 5900/81

Brands by name

Popular brands

Minebea Intec Maxxis 5 Phase PR 5900/81, Operating Instructions Manual

Search results

Summary of Contents for Maxxis 5 Phase PR 5900/81

Reviews:

Related manuals for Maxxis 5 Phase PR 5900/81

Brands by name

Popular brands