Miele WWI 860 Operating Instructions Manual Download Page 71

Page: 71 / 108

Problem solving guide

Fault messages at the end of a programme

Problem

Possible cause and remedy



Align the washing
machine

The

Pre-ironing

Extra at the end of the programme

could not be carried out properly.



Check whether the washing machine is aligned
correctly (see "Installation – Levelling the
machine").



Check whether the maximum drain height of 1 m
has been exceeded.

If the fault message appears again, contact Miele. The
washing machine can still be used, but without the

Pre-ironing

Extra.



Check jet

The pumps are dirty.



Clean the pumps as described in "Problem solving
guide – Opening the door in the event of a blocked
drain outlet and/or power cut".



Restart the programme after cleaning.

The jet in the top of the door ring is blocked with fluff.



Remove the fluff with your finger. Do not use any
sharp or pointed tools to do this.



Restart the programme after cleaning.

If the fault message appears again, contact Miele. The
washing machine can still be used but with reduced
functionality.

The messages will appear at the end of the programme and when the washing
machine is switched on and need to be confirmed with the

sensor.

Summary of Contents for WWI 860













































































































Search results

Summary of Contents for WWI 860

Reviews:

Related manuals for WWI 860

Brands by name

Popular brands

Miele WWI 860, Operating Instructions Manual

Search results

Summary of Contents for WWI 860

Reviews:

Related manuals for WWI 860

Brands by name

Popular brands