Miele G 673 Operating Instructions Manual Download Page 65 | Manualshive

Page: 65 / 84

background image

I

Adjust the rear screw feet to the re-
quired height.

Higher = turn clockwise

Lower = turn anti-clockwise

Several turns are needed to adjust 1
mm in height. A battery powered screw-
driver could be used.

Adjust the front screw feet manually
or with a flat blade screwdriver.

It is easier to adjust the screw feet if the
weight of the dishwasher is not bearing
down on them.

If possible tip the machine slightly.

For fine adjustments it may be
necessary to press with a screw-
driver against the cogs of the feet.

Screw the feet out until the dishwasher
is right up against the underside of the
worktop, to which it will be screwed
later. Ensure that the dishwasher
stands level.

Installation

65

«
...
63
64
65
66
67
...
»

Summary of Contents for G 673





















































































Reviews:

No comments

Related manuals for G 673

Brand: Black+Decker Pages: 36

Brand: Hanseatic Pages: 72

Brand: Daewoo Pages: 36

Brand: Maidaid Halcyon Pages: 15

Brand: Asko Pages: 59

Brand: Hotpoint Ariston Pages: 36

Brand: Valencia Euro Pages: 21

Hotpoint HDA3400G

Brand: Hotpoint Pages: 2

Brand: Bush Pages: 48

Brand: Fisher & Paykel Pages: 40

Brand: Smeg Pages: 2

Brand: Daewoo Pages: 57

Brand: Samsung Pages: 44

Brand: FAR Pages: 98

Brand: Samsung Pages: 44

Brand: Samsung Pages: 48

WA13J571 Series

Brand: Samsung Pages: 44

Brand: Frigidaire Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands