Miele G 673 Operating Instructions Manual Download Page 51

Page: 51 / 84

Problem solving guide

With the aid of the following explana-
tory notes, minor faults can be cor-
rected without contacting the Miele Ser-
vice Department.

Any work on the electrical compo-
nents of the appliance should only
be carried out by a suitably quali-
fied and competent person in ac-
cordance with local and national
regulations. Unauthorised repairs
could be dangerous.

If, however, you are unable to correct
the problem, the Miele Service Depart-
ment should be contacted.

Faults/possible causes

The dishwasher does not start

– The door is not properly closed.

– The plug is not properly inserted.

– The fuse is defective/has blown.

Shortly after starting a programme
the dishwasher stops working

– The stopcock is shut.

Open the door and see if the indicator
light for the programme selected is
flashing.

Open the stopcock and close
the door.
The dishwasher should continue
the programme.

If the programme does not continue,
switch the dishwasher off and then on
again.

The dishes are not clean

– The dishes are incorrectly loaded.

– The wrong amount of detergent was

used - see "Programme chart".

– The filters in the wash cabinet are

not clean - see “Cleaning and care”.

– Spray arm jets are blocked - see

“Cleaning and care”.

– The wrong programme was selected

- see "Programme chart".

Problem solving guide

Summary of Contents for G 673





















































































Search results

Summary of Contents for G 673

Reviews:

Related manuals for G 673

Brands by name

Popular brands

Miele G 673, Operating Instructions Manual

Search results

Summary of Contents for G 673

Reviews:

Related manuals for G 673

Brands by name

Popular brands