Miele G 673 Operating Instructions Manual Download Page 70 | Manualshive

Page: 70 / 84

background image

Fitting the door front

The door front is correctly fitted when:

– the lower lugs of the fixing bracket

rest firmly in the lower slits of the
dishwasher outer door panel.

– The prongs of the fixing bracket lie

on the sprung bolts in the upper cor-
ners of the dishwasher door.

Pull the dishwasher out of the recess
enough for the door front fixing
screws to be easily accessible, and
the upper edge of the dishwasher
door to be unobstructed by the work
top.

Hang the door front so that the lower
lugs of the fixing bracket fit into the
lower slits of the dishwasher outer
door panel, and draw slightly up-
wards.

Installation

70

«
...
68
69
70
71
72
...
»

Summary of Contents for G 673





















































































Reviews:

No comments

Related manuals for G 673

Brand: Campomatic Pages: 25

Brand: saco Pages: 5

Brand: Baumatic Pages: 28

Brand: ZANKER Pages: 28

Brand: Euromaid Pages: 33

Brand: Alliance Laundry Systems Pages: 24

Brand: Alliance Laundry Systems Pages: 24

Brand: Rangemaster Pages: 28

Brand: Hotpoint Ariston Pages: 36

Brand: Asko Pages: 28

Brand: Swissh Pages: 12

Brand: IKEA Pages: 16

Brand: John Lewis Pages: 32

Brand: Ariston Pages: 16

Brand: Samsung Pages: 11

WF405ATPAWR/AA-0001

Brand: Samsung Pages: 132

Brand: Samsung Pages: 160

Brand: Samsung Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands